Home / Products / Sleeve Box Bending Machine

Sleeve Box Bending Machine

Sleeve Box Sheet Bender · Coaming Box Panel Bender · Sleeve Box Sheet Bending Machine

This machine is known by other names depending on who is asking — See all names.

The No.0 PP honeycomb sleeve box bending machine creases or bends plastic honeycomb panels so that the sleeve panels can be folded into shape. It is a key station of a sleeve box line and usually works together with panel cutting, window opening, edge banding and joining.

  • Processing thickness0.5–30 mm
  • Processing width1.6 m
  • Max board length3.5 m (3-station) / 6 m (6-station)

Panels: PP honeycomb panels, plastic hollow boards, rice-shaped hollow boards, S-shaped hollow boards. Supplied by No.0 Machinery, Shanghai / Changzhou, China.

Sleeve Box Bending MachineSleeve Box Bending MachineSleeve Box Bending MachineSleeve Box Bending MachineSleeve Box Bending MachineSleeve Box Bending MachineSleeve Box Bending MachineSleeve Box Bending Machine

Overview

The No.0 PP honeycomb sleeve box bending machine creases or bends plastic honeycomb panels so that the sleeve panels can be folded into shape. It is a key station of a sleeve box line and usually works together with panel cutting, window opening, edge banding and joining.

Unlike a metal press brake, it does not force a sharp bend: it pre-forms a controlled crease line, so the honeycomb core is not crushed and the surface does not crack. The crease becomes the folding datum of the box.

How it works

A heating unit softens the crease area first; a hydraulically driven die then presses the softened panel into a crease. Because the material is formed while soft, the surface stays intact and the crease does not fracture.

The machine is available with 3 or 6 stations and one-time forming. Carbon-fibre heaters bring the die area up to temperature quickly, and the heated die runs up to 200 °C so the crease is formed evenly along the full length.

A full-touch HMI runs one-key automatic production, with manual and automatic modes switchable. Temperature, time and pressure recipes can be stored per panel type and thickness.

Processable panels

PP honeycomb panels, plastic hollow boards, rice-shaped hollow boards, S-shaped hollow boards

Typical industries

Packaging, automotive, electronics, electrical appliances, new energy

Machine advantages

Heating and forming

  • Carbon-fibre heaters: one full sheet finished in 40 seconds, including heating
  • Heated die up to 200 °C: clean crease, low spring-back, no cracking after repeated folding
  • Minimum crease spacing 260 mm, adjustable crease pitch for different box sizes

Stations and capacity

  • 3-station model: 150 t, board length 3.5 m — 6-station model: 300 t, board length 6 m
  • Processing width 1.6 m, panel thickness 0.5–30 mm
  • One-time forming: all creases of one panel in a single pass

Operation and control

  • Full-touch HMI, one-key automatic production, manual / automatic switchable
  • Recipes stored by panel type and thickness: change batch without re-setting the die
  • 4-point mechanical balance keeps the panel square and the crease line straight
The No.0 sleeve box bending machine turns flat honeycomb panels into foldable box walls — from one panel to a full ring of walls, every crease under control.

Three problems in manual creasing

Manual bending has three bottlenecks: waiting for heat, creases that crack, and recipes that have to be re-learned by every operator. The No.0 bending machine is designed around these three points.

01

Fast heating

A full sheet in 40 seconds

Carbon-fibre heaters concentrate heat, so one whole sheet — heating included — is finished in 40 seconds. Compared with conventional heating the waiting time drops and the cycle stays stable.

02

No cracking

Heated die up to 200 °C

The forming die is heated to 200 °C. The panel is pressed while soft: the crease is clean, spring-back is small, and repeated folding does not break the panel — even in winter, on thick panels or at sharp angles.

03

One-key operation

Recipes replace experience

Press one key to start; temperature, time and pressure are stored per panel and thickness. Changing batch does not need a new trial, and a new operator can run the machine after half an hour of training.

Summary: turn experience into recipes.

FAQ

How thick a panel can the bending machine process?

0.5–30 mm, depending on the model. PP honeycomb panels and plastic hollow boards are both supported.

Should I choose the 3-station or the 6-station model?

3-station: 150 t total pressure, board length up to 3.5 m. 6-station: 300 t, board length up to 6 m. Choose by the largest box perimeter you need to produce.

How much does a bending machine cost?

Price depends on stations, pressure, working width and automation. Send your panel type, thickness, box size and target output for a configuration and quotation.

Where is the machine built and how is it supported?

Machines are assembled and test-run at the No.0 plant in Changzhou, Jiangsu, then shipped. Installation, commissioning and spare parts are supported directly by the manufacturer.

Specifications

Processing thickness0.5–30 mm
Processing width1.6 m
Max board length3.5 m (3-station) / 6 m (6-station)
Stations3 or 6, one-time forming
Total pressure150 t (3-station) / 300 t (6-station)
Cycle40 seconds per sheet, heating included
Creases per panelSix creases typical, set by box type
Minimum crease spacing260 mm
HeatingFar-infrared carbon-fibre heaters
Die temperatureUp to 200 °C
ControlFull-touch HMI, one-key automatic / manual

Need a quotation or a line layout? Send your panel size, thickness and target output.

Request a quoteWhatsApp