Home / Products / PP Honeycomb Board Pallet Sleeve Box Joining Machine

PP Honeycomb Board Pallet Sleeve Box Joining Machine

PP Honeycomb Coaming Box Joining Machine · Joining Machine for PP Honeycomb Coaming Box

This machine is known by other names depending on who is asking — See all names.

The No.0 PP honeycomb sleeve box joining machine welds the two ends of a cut and creased panel into a closed sleeve frame — the last weld that turns a flat panel into a ring of box walls.

  • Processing thickness3–20 mm
  • Joining length1.6 m
  • Cycle25 seconds per weld

Panels: PP honeycomb panels, plastic hollow boards, rice-shaped and S-shaped hollow boards; plastic grades PP, PVC, PE, PVDF, ABS. Supplied by No.0 Machinery, Shanghai / Changzhou, China.

PP Honeycomb Board Pallet Sleeve Box Joining MachinePP Honeycomb Board Pallet Sleeve Box Joining MachinePP Honeycomb Board Pallet Sleeve Box Joining MachinePP Honeycomb Board Pallet Sleeve Box Joining MachinePP Honeycomb Board Pallet Sleeve Box Joining MachinePP Honeycomb Board Pallet Sleeve Box Joining MachinePP Honeycomb Board Pallet Sleeve Box Joining MachinePP Honeycomb Board Pallet Sleeve Box Joining Machine

Overview

The No.0 PP honeycomb sleeve box joining machine welds the two ends of a cut and creased panel into a closed sleeve frame — the last weld that turns a flat panel into a ring of box walls.

The main difference from manual welding: no filler rod and no chamfering. The panel edges are heated until molten, then pressed together by pneumatic force, so the weld is formed by the panel's own melt.

How it works

Three steps: heat to melt, press to join, cool to set.

Spiral stainless-steel heaters distribute heat evenly along the seam; heating time and temperature are set per material and thickness. A pneumatic drive pushes the two panels together while a 4-point balance system keeps pressure and feed speed identical at all four points, so the seam does not end up tight on one side and loose on the other.

A 7-inch full-touch control system offers manual and automatic modes. The manual screen lists every step in working order to avoid mis-operation; the automatic screen runs the stored recipe for repeated production.

Processable panels

PP honeycomb panels, plastic hollow boards, rice-shaped and S-shaped hollow boards; plastic grades PP, PVC, PE, PVDF, ABS

Typical industries

Packaging, automotive, electronics, electrical appliances, new energy

Machine advantages

Weld quality

  • No filler rod, no chamfering, no seam bleeding: the panel welds with its own melt
  • Flat, strong seam: level table, edges aligned, uniform weld face

Accuracy and consistency

  • 4-point mechanical balance: identical pressure and speed at all four driving points
  • Adjustable joining pressure per thickness: thin panels are not over-pressed, thick panels weld through

Operation and efficiency

  • No.0 joining machine control system: 7-inch touch screen, manual / automatic, one-key production
  • Recipes saved by material, thickness and length
  • Independent foot pedals for left and right clamps; fold-away support bracket saves floor space
The No.0 sleeve box joining machine welds a panel into a closed frame: no filler rod, no chamfering, no leakage — even seams, strong welds, and the same result whoever runs it.

Four problems in manual joining

Manual joining is afraid of three things: uneven pressure at the two ends, a seam that is not fully welded, and a new operator having to re-adjust everything. The No.0 joining machine addresses balance, heating and operation.

01

4-point balance

Identical force and speed

Four driving points keep the same pressure and feed speed, so the panel is loaded evenly and the seam is not tight on one side and loose on the other. The joined panel stays flat and square for the next crease.

02

Spiral heater

Even heat, stronger weld

A spiral stainless-steel heater distributes heat along the seam, so both panel ends reach the same temperature. Local cold spots or burnt areas are avoided and the weld is stronger and cleaner.

03

Dedicated control system

One key, stable cycle

The No.0 joining machine control system starts the sequence with one key; the motion order is controlled by the system instead of by hand, which stabilises the cycle and daily output.

04

Recipes and electronic pressure

Anyone can run it

Temperature, time and pressure are stored per panel and thickness; electronic pressure setting replaces manual knobs, so the result repeats. A new operator is productive after half an hour.

Summary: even seams, strong welds — and the same result whoever runs it.

FAQ

Does joining need a filler rod or chamfering?

No. The machine welds with the panel's own melt, so no filler rod, no chamfering and no seam bleeding.

What panel length and thickness can it join?

Joining length 1.6 m, panel thickness 3–20 mm; a single weld takes about 25 seconds.

Which plastic grades can be joined?

PP, PVC, PE, PVDF and ABS panels, in honeycomb or hollow-board structure.

Will the joined seam leak?

The seam is closed by the panel's own melt under pressure, so there is no open seam and no leakage — unlike manual welding, which often leaves pin-holes.

Specifications

Processing thickness3–20 mm
Joining length1.6 m
Cycle25 seconds per weld
Power3 kW
Welding methodHot-melt butt joining, no filler rod, no chamfering
HeatingSpiral stainless-steel heaters along the seam
DrivePneumatic, 4-point balance
ControlNo.0 joining machine control system, 7-inch touch screen
AuxiliaryFold-away bracket, independent foot pedals for both clamps
Panel gradesPP, PVC, PE, PVDF, ABS

Need a quotation or a line layout? Send your panel size, thickness and target output.

Request a quoteWhatsApp