Home / Products / PP Honeycomb Board Sleeve Box Edge Banding Machine

PP Honeycomb Board Sleeve Box Edge Banding Machine

Edge Banding Machine for PP Honeycomb Board Sleeve Boxes · PP Honeycomb Coaming Box Edge Banding Machine · PP Honeycomb Board Pallet Sleeve Box Edge Banding Machine

This machine is known by other names depending on who is asking — See all names.

The No.0 PP honeycomb sleeve box edge banding machine closes the sharp, ragged, open edge left by cutting. Heat and pressure close and flatten the edge so it is smooth, strong and safe to handle.

  • Power supply380 V
  • Power24 kW
  • Banding width0.3–1.5 m (narrower than 0.3 m cannot be banded)

Panels: Plastic hollow boards, rice-shaped hollow boards, S-shaped hollow boards, plastic honeycomb panels. Supplied by No.0 Machinery, Shanghai / Changzhou, China.

PP Honeycomb Board Sleeve Box Edge Banding MachinePP Honeycomb Board Sleeve Box Edge Banding MachinePP Honeycomb Board Sleeve Box Edge Banding MachinePP Honeycomb Board Sleeve Box Edge Banding MachinePP Honeycomb Board Sleeve Box Edge Banding MachinePP Honeycomb Board Sleeve Box Edge Banding MachinePP Honeycomb Board Sleeve Box Edge Banding MachinePP Honeycomb Board Sleeve Box Edge Banding Machine

Overview

The No.0 PP honeycomb sleeve box edge banding machine closes the sharp, ragged, open edge left by cutting. Heat and pressure close and flatten the edge so it is smooth, strong and safe to handle.

The process is self-sealing by heat: no tape and no glue. The panel's own plastic softens, is pressed together and sets, so the edge is closed with the same material as the panel.

How it works

Four steps: feed, heat, press, trim.

Feed: the panel moves along the track at an adjustable speed. Heat: both parallel edges pass the hot-air zone — four heater groups per side, in four independently controlled zones — until the plastic becomes formable; temperature and heater distance are set per material and thickness.

Press: the softened edges enter the pressing unit, where rollers or dies with a gap smaller than the panel thickness force the two skins together, closing and flattening the open edge. Trim: the remaining burr is cut off, leaving a flat, smooth band.

Processable panels

Plastic hollow boards, rice-shaped hollow boards, S-shaped hollow boards, plastic honeycomb panels

Typical industries

Packaging, automotive, electronics, electrical appliances

Machine advantages

Line integration

  • Fully automatic line-type banding: feed, heat, band and cut in one flow, speed adjustable
  • Double-sided operation with high-temperature, high-pressure belts keeps both edges symmetrical

Heating system

  • Hot-air heating with 4 heater groups per side, in 4 independently controlled zones
  • Zone control reduces wasted energy; different materials and thicknesses get their own heat setting

Structure and accuracy

  • Steel frame: stable, does not deform when the machine is moved
  • 4-point mechanical synchronisation: identical line speed, no panel drift, even band width

Finish and safety

  • Hot-melt roller forming: flat, tight, gap-free band that survives repeated folding
  • Corner rounding unit: the finished edge will not cut hands
  • Cool-down after stop: heaters shut off first, then cool, protecting the control parts from heat回流
The No.0 edge banding machine uses no tape and no glue: hot air softens the panel edge, pressure fuses the two skins into one flat sealed band — a closed edge is a durable box.

Four problems in edge banding

Edge banding usually fails on four points: speed, a burr that cuts hands, heat flowing back after a stop, and panels that drift. The No.0 edge banding machine is designed around them.

01

Four heater groups per side

Up to 6 m/min

Hot-air heating with four groups per side in four zones: the panel keeps receiving heat as it moves, so the banding speed reaches 6 m per minute without trading quality for speed.

02

Corner rounding unit

No sharp edge

After banding, the corner is rounded so the finished edge is smooth and does not cut hands; one manual trimming step is removed and packing is safer.

03

Cool-down after stop

Protects the control parts

Heaters stop first, then the unit cools down. Residual heat cannot flow back and damage control components or heating elements, so the machine lasts longer and unplanned stops are fewer.

04

4-point synchronisation

No drift, even band width

A timing belt with 4-point mechanical synchronisation keeps line speed identical at all four points: the panel does not drift or skew and the band width stays even on long and thin panels.

Summary: fast banding, smooth edge, no drift.

FAQ

What banding width and thickness are supported?

Banding width 0.3–1.5 m; panels narrower than 0.3 m cannot be banded. Maximum panel thickness 20 mm.

How fast is the banding?

Up to 6 m per minute with 24 kW of heating, four heater groups per side.

Does banding need tape or glue?

No. The edge is closed by the panel's own melt — no consumables, no glue lines.

Is the corner rounding unit standard?

Yes. Corner rounding, cool-down after stop and 4-point synchronisation are standard on this model.

Specifications

Power supply380 V
Power24 kW
Banding width0.3–1.5 m (narrower than 0.3 m cannot be banded)
Max panel thickness20 mm
HeatingHot air, 4 heater groups per side
Sealing stations2 (both edges)
Banding methodHot-melt self-sealing, no tape, no glue
SpeedUp to 6 m/min
Heating control4 zones, independent, constant temperature
ConveyorHigh-temperature high-pressure belt, 4-point synchronisation
Standard equipmentCorner rounding unit, cool-down after stop, 4-point sync
FrameSteel frame

Need a quotation or a line layout? Send your panel size, thickness and target output.

Request a quoteWhatsApp